by Crandall on March 9th, 2008

Question

Help answer this question below.

My 1990 Acura Integra Is throwing a code which is a cam shaft posstioning sensor which is built into the distributor. I tryed 3 different distributor and the same code is flasing on the computer. The car wont run right or at all. Whats the problem?

Like
Report

Share:: Facebook; Twitter; Other

Answers. 1 helpful answer below.

by civickid on September 7th, 2008
Have you verfied the wiring going back to your ecm?
Comments
Add a comment...
- Like
- Report
No comments. Post one | Permalink

Did this answer your question? If not, then ask a new question or create a poll.

More Questions. Additional questions in this category.

I have a 1.8 doch 95 integra ls. i want to know if other fuel injectors will fit my engine? will it give it more power?
by junior5001 on January 24th, 2009 | 1 person likes this
Transmission Slips on 1992 Honda Integra ZXI, Why?
by ToyBoy on January 9th, 2012 | 1 person likes this
I have a 91 Acura Integra. The Driver side cooling fan goes on after car is off. Not overheating.fanswitchandrelay was replace. What Wrong?
by Integra91220 on October 5th, 2010 | 1 person likes this
I have a 1989 acura integra 24 valve V6 2700 engine that is hard to start an when its started black smoke come out of the tail pipe.... WHAT IS IT?
by wsmikey on December 11th, 2008 | 1 person likes this
cant remove the crankshaft pulley from 1988 acura integra i cant find a tool and my snap on impact isnt enough
by blohmg on August 4th, 2010 | 1 person likes this
More Acura Integra See only professionally researched Acura Integra questions

You're reading My 1990 Acura Integra Is throwing a code which is a cam shaft posstioning sensor which is built into the distributor. I tryed 3 different distributor and the same code is flasing on the computer. The car wont run right or at all. Whats the problem?

Follow us on Facebook!

Related Ads

Professionally Researched

ANSWERBAG BUZZ

Integra 1990 how to read codes

Codes for a 1990 acura integra

1990 integra codes

1990 acura integra code 3

1990 acura integra uk

About Us

About Answerbag

Sitemap

Professionally Researched Questions

Legal

Privacy Policy

Terms of Use

Disclaimer

Ad Choices
Follow Us on Facebook

Answerbag.com
Your favorite Q&A site is on Facebook! Become a fan to connect with the ever-growing community of Answerbaggers, share your thoughts and find out what Answerbag's up to next!
Latest Tweet

What is a movie that was ignored you thought great? http://t.co/FsBFmVd7

Follow Answerbag on Twitter!

Answerbag

Question

My 1990 Acura Integra Is throwing a code which is a cam shaft posstioning sensor which is built into the distributor. I tryed 3 different distributor and the same code is flasing on the computer. The car wont run right or at all. Whats the problem?

Answers. 1 helpful answer below.

Comments

Did this answer your question? If not, then ask a new question or create a poll.

More Questions. Additional questions in this category.

Follow us on Facebook!

Related Ads

Related Questions

My 1990 Acura, Integra has no spark, resulting in failure to turn on. What are the common possibilities? I have changed the distributor cap, rotor and spark plugs. No results yet!

Acura Integra 1990. While driving, the car has died - 3 times now. Charging the drained battery helps briefly, then it dies again. Alternator apparently good. Battery recently replaced. Car died today but ran fine while hooked up to a portable booster.

1990 acura integra will not charge. Need to find location of solenoid (is that spelled right)? I do not have the manual and need a diagram of everything so that I can get some help in finding a way to get this car to someone to fix.

1991 Acura integra, starts easily and runs fine until recently. Operates fine for a day, maybe two, sometimes a week and then will loose power like ignition turned off. Have replaced: ignition module, injector relay, and distributor. Any thoughts . Thanx.

1990 mercury cougar 3.8L supercharged. i replaced the cam shaft sensor how do you set the timing the car runs but the rpm wont come down idles at 2500.

Professionally Researched

How fast is the Acura Integra'92 B18 car?

Why are there three wires in a Mustang car distributor?

What is a car distributor cap?

What does Acura service code"A12"mean?

What does the acura tl 2002 radio code serial number 30047095 mean?

ANSWERBAG BUZZ

Answerbag.com
Your favorite Q&A site is on Facebook! Become a fan to connect with the ever-growing community of Answerbaggers, share your thoughts and find out what Answerbag's up to next!

Question

My 1990 Acura Integra Is throwing a code which is a cam shaft posstioning sensor which is built into the distributor. I tryed 3 different distributor and the same code is flasing on the computer. The car wont run right or at all. Whats the problem?

Answers. 1 helpful answer below.

Comments

Did this answer your question? If not, then ask a new question or create a poll.

More Questions. Additional questions in this category.

Follow us on Facebook!

Related Ads

Related Questions

Professionally Researched

ANSWERBAG BUZZ

Answerbag.com Your favorite Q&A site is on Facebook! Become a fan to connect with the ever-growing community of Answerbaggers, share your thoughts and find out what Answerbag's up to next!

Answerbag.com
Your favorite Q&A site is on Facebook! Become a fan to connect with the ever-growing community of Answerbaggers, share your thoughts and find out what Answerbag's up to next!