"Remove the Flow Restrictor All shower heads and hand held shower head sets sold in the United States contain a flow restrictor, also known as a flow controller, as required by the National Energy Act that limit water flow to 2.5 gallons per minute. This helps save water and energy, which could help you save money on your utility bill. Removing the shower head or hand held shower flow restrictor will increase your water and energy consumption. It will also increase the amount of water flowing through your shower head or hand held shower head for increased water pressure through your shower head or hand held shower. To remove the flow restrictor, remove the shower head from the shower arm supply pipe or the hand held shower head from the hand held shower hose. If you cannot remove the shower head by hand, use a rag and a wrench – the rag will help protect your shower head's finish. Depending on the model, you may need to remove the gasket, which is a small, black, donut-shaped piece of rubber in the shower head inlet or hand held shower's handle. Use a long skinny tool like a slotted screwdriver to carefully pull the gasket from the shower head inlet. Remove the gasket carefully so you do not damage the shower head threads. Also be careful not to tear the gasket. If you do tear it, don't reuse it. When you reinstall the shower head, use Teflon tape instead. The flow restrictor is the piece of plastic at the inlet of the shower head or hand held shower head's handle. Sometimes it's pink and behind a star-shaped piece of metal. sometimes it's green. Other manufacturers make theirs white. Whatever the color, remove these pieces by using a long, thin tool like a slotted screwdriver. Catch an edge of the flow controller or restrictor with the corner of the screwdriver and give the piece a twist with your wrist. The flow restrictor will pop out of the shower head or hand held shower. If you live in an area of low water pressure, removing the flow restrictor will not substantially change the pressure you get through the shower head or hand held shower head. Check our section on "shower heads and hand held showers that are good for low pressure areas." Remember, by removing the flow restrictor your utility bill may increase. You will also be using more of our natural resources. Keep the restrictor handy in case your want to re-install in your shower head or hand held shower in the future." http://www.showerstore.com/support/water-pressure.html

"Remove the Flow Restrictor All shower heads and hand held shower head sets sold in the United States contain a flow restrictor, also known as a flow controller, as required by the National Energy Act that limit water flow to 2.5 gallons per minute. This helps save water and energy, which could help you save money on your utility bill. Removing the shower head or hand held shower flow restrictor will increase your water and energy consumption. It will also increase the amount of water flowing through your shower head or hand held shower head for increased water pressure through your shower head or hand held shower. To remove the flow restrictor, remove the shower head from the shower arm supply pipe or the hand held shower head from the hand held shower hose. If you cannot remove the shower head by hand, use a rag and a wrench – the rag will help protect your shower head's finish. Depending on the model, you may need to remove the gasket, which is a small, black, donut-shaped piece of rubber in the shower head inlet or hand held shower's handle. Use a long skinny tool like a slotted screwdriver to carefully pull the gasket from the shower head inlet. Remove the gasket carefully so you do not damage the shower head threads. Also be careful not to tear the gasket. If you do tear it, don't reuse it. When you reinstall the shower head, use Teflon tape instead. The flow restrictor is the piece of plastic at the inlet of the shower head or hand held shower head's handle. Sometimes it's pink and behind a star-shaped piece of metal. sometimes it's green. Other manufacturers make theirs white. Whatever the color, remove these pieces by using a long, thin tool like a slotted screwdriver. Catch an edge of the flow controller or restrictor with the corner of the screwdriver and give the piece a twist with your wrist. The flow restrictor will pop out of the shower head or hand held shower. If you live in an area of low water pressure, removing the flow restrictor will not substantially change the pressure you get through the shower head or hand held shower head. Check our section on "shower heads and hand held showers that are good for low pressure areas." Remember, by removing the flow restrictor your utility bill may increase. You will also be using more of our natural resources. Keep the restrictor handy in case your want to re-install in your shower head or hand held shower in the future." http://www.showerstore.com/support/water-pressure.html