by lwrdrchevs on February 15th, 2007

Question

Help answer this question below.

How do you remove the dash from a '66 chevy c10 pickup after you remove the 6 side bolts? is it seated under the windshield seal?

Like
Report

Share:: Facebook; Twitter; Other

Answers. 1 helpful answer below.

by Anonymous on September 14th, 2007
Now this is just theory because I own an 83, but somethings never change with GM. :) Try taking out the vents in your dash that channel the airflow for your heater and climate control. Often GM will hide bolts behind these and they should popout-pop in. There may also be vents on the top of the dash for defrosting of the windshield. Look under these as well. Good luck!
Comments
Add a comment...
- Like
- Report
No comments. Post one | Permalink

Did this answer your question? If not, then ask a new question or create a poll.

More Questions. Additional questions in this category.

I have a 1966 Chevrolet pickup with a three speed shifter on the column. I would like to change it to three speed on the floor. Do I have to change the entire transmission or can I just change the linkage setup?
by ardsee on January 19th, 2008 | 1 person likes this
I have79 luv thought accelorator pump was bad has bad spot in acceleration where it seems like its not getting proper fuel but reves at idle
by jdhutchens1122 on March 21st, 2012 | 1 person likes this
What is the sequence on a 1951 chevy truck, manual transmission
by joejoe on July 29th, 2008 | 1 person likes this
What trailer brake controller should i use on a 68 chevy 3/4 ton
by cheese on January 20th, 2008 | 1 person likes this
I need to know how to tune a rochester carb qudrajet it is a 4bbl it is for my 1975 chevy pickup or how many turns on the carb to get the right settings i talking about the fuel mixture. the motor is a 350 and automatic transmission th350
by harrison on June 13th, 2008 | 1 person likes this
More Pre-1980 trucks and SUVs See only professionally researched Pre-1980 trucks and SUVs questions

You're reading How do you remove the dash from a '66 chevy c10 pickup after you remove the 6 side bolts? is it seated under the windshield seal?

Follow us on Facebook!

Related Ads

Professionally Researched

ANSWERBAG BUZZ

How to remove windshield out chevy c10

How to remove windshield 66 chev c10

66 chev dash removal

Transmission removal 66 chevy c10

Shifter handles for chevy c10 pickup

About Us

About Answerbag

Sitemap

Professionally Researched Questions

Legal

Privacy Policy

Terms of Use

Disclaimer

Ad Choices
Follow Us on Facebook

Answerbag.com
Your favorite Q&A site is on Facebook! Become a fan to connect with the ever-growing community of Answerbaggers, share your thoughts and find out what Answerbag's up to next!
Latest Tweet

What is the very worst thing you can do in an interview? http://t.co/3QoM2mLE

Follow Answerbag on Twitter!

Answerbag

Question

How do you remove the dash from a '66 chevy c10 pickup after you remove the 6 side bolts? is it seated under the windshield seal?

Answers. 1 helpful answer below.

Comments

Did this answer your question? If not, then ask a new question or create a poll.

More Questions. Additional questions in this category.

Follow us on Facebook!

Related Ads

Related Questions

I want to replace the gear shift handle on my 1975 Chevy c10 pick-up w/auto trans. When I remove the handle, will any parts drop down inside of the steering column or will they stay in place until I insert the new handle?

My 1975 Chevrolet C10 pickup that has a 350 engine with 350 turbo transmission has fluid leaks on the two center bolts on the right side of the intake below the carb, what would cause transmission fluid to be on top of my engine?

I am replacing a heater core in a 76' c-10 with AC, where are all the mounting bolts for the air box? I found one on the right side, the rest have a "round" head on them, If these are the mounting screws how can i get them out?

I NEED TO KNOW IF ANY BODY CAN TELL ME HOW TO REMOVE KEY SWITCH FROM A 1974 CHEVY PICKUP COLUMN I HAVE PUSHED SHOVED PUT SCREWDRIVERS IN SLOTS NO LUCK HELP LOST WITH OUT MY TRUCK

I am trying to remove the two bolts from oil filter flange on a 1994 Chevy K2500. I cannot locate the correct tool to use to remove the what appears to be square bolts. Any ideas on what tool to use to remove the bolts?

Professionally Researched

How do I remove molly bolts?

How do I remove rusted on toilet seat bolts?

How do I remove hard water stains from a windshield?

How do I remove solder with a hot air gun?

How do I remove smoke film from mounted fish?

ANSWERBAG BUZZ

Answerbag.com
Your favorite Q&A site is on Facebook! Become a fan to connect with the ever-growing community of Answerbaggers, share your thoughts and find out what Answerbag's up to next!

Question

How do you remove the dash from a '66 chevy c10 pickup after you remove the 6 side bolts? is it seated under the windshield seal?

Answers. 1 helpful answer below.

Comments

Did this answer your question? If not, then ask a new question or create a poll.

More Questions. Additional questions in this category.

Follow us on Facebook!

Related Ads

Related Questions

Professionally Researched

ANSWERBAG BUZZ

Answerbag.com Your favorite Q&A site is on Facebook! Become a fan to connect with the ever-growing community of Answerbaggers, share your thoughts and find out what Answerbag's up to next!

Answerbag.com
Your favorite Q&A site is on Facebook! Become a fan to connect with the ever-growing community of Answerbaggers, share your thoughts and find out what Answerbag's up to next!