- NEW!
Questions and answers about the ignition control module in your engine
where is the ignition control module on a 1998 ford contour
by babs64 on April 30th, 2012
|
one answer
|
in Ignition control module
by Anonymous on December 31st, 1969
|
no answers
|
in
Ford ranger ignition switch wont shut off
by miami on December 5th, 2009
|
no answers
|
in Ignition control module
1988 silvardo 1500 MT SURGES ON HIGHWAY AND SOME TIMES GOES INTO HALF THROTTLE WHEN PEDAL IS WIDE OPEN
by dutchman2 on November 10th, 2009
|
no answers
|
in Ignition control module
I have gas in my oil i have an 2005 nissan sentra 1.8L when i crank it it takes two or three cranks to start now it wont start.Also when it would crank it shimmeys at first
by mikes7209 on November 8th, 2009
|
2 answers
|
in Ignition control module
I have 05 nissan altima all the electrical lights up but the engine will not turn over, is possibily battery, alternator, or starter?
by Anonymous on October 30th, 2009
|
one answer
|
in Ignition control module
94 Blazer 4.3 cpi vortex fuel pump went out melted wires changed the pump got gas to test valve changed cpi (spider) gets gas no start i hand feed gas it will start told its the crankshaft sensor bought one left side timing chain cover not there where!
by Anonymous on October 9th, 2009
|
one answer
|
in Ignition control module
I have a 95 Cutlass Ciera. When I put the car in park and turn the key off, the engine keeps running. Sometimes it will shut off nomally. I usually turn the key back on and back up and go forward a few feet and then it will turn off with the key. Help!
by debbiec916 on September 11th, 2009
|
one answer
|
in Ignition control module
I have a 1990 Chevrolet Suburban R2500, I cant locate the tan wire with the Black stripe. I am in the cab ready to dismantle the entire dashboard. trying to set timing on this truck. the service engine soon light will not go out either. need help. 350 en
by Acarter1950 on August 17th, 2009
|
no answers
|
in Ignition control module
2004 ford focus station wagon stuttering like runing lean but is not/ or it acts like it will choke down but it doesnot .
by monkey on June 29th, 2009
|
no answers
|
in Ignition control module
I HAVE A 1988 NISSAN PICKUP TRUCK THAT WILL NOT START. HAVE CHANGED SPARK PLUGS, WIRES AND DISTRIBUTOR CAP, ROTOR. ANY SUGGESTIONS?
by Anonymous on April 3rd, 2009
|
2 answers
|
in Ignition control module
1994 k1500 starts and runs fine going to work after work it will not start turns over no fire the next day will start and run fine replaced fuel filter done this for a week?
by Anonymous on April 1st, 2009
|
one answer
|
in Ignition control module
How do i replace an ignition switch in a 1997 ford ranger?
by Anonymous on March 23rd, 2009
|
one answer
|
in Ignition control module
2003 Jeep Wrangler: Battery seems fine. Does not start (even turn over at all). Instruments such as speedometer and tach are jumping all over the place (with key in "on" and "off" position)! Please Help!
by Jay on March 16th, 2009
|
one answer
|
in Ignition control module
Why does my 2001 ford taurus misfire when the A/C compressor ie on?
by acadata on March 11th, 2009
|
one answer
|
in Ignition control module
Where is located the computer in the engine for Pontiac sunfire 1996 (diagram) please
by Anonymous on March 9th, 2009
|
2 answers
|
in Ignition control module
1994 Ford Ranger 3.0L has worn out the gears on two distributors. Does this indicate a bad cam gear drive? The last distributor lasted a year. What can cause this problem?
by Anonymous on March 9th, 2009
|
one answer
|
in Ignition control module
What would make my 1996 4cyl grand am stop when it comes up on compression?
by doylec on February 9th, 2009
|
one answer
|
in Ignition control module
My BMW 325i is cranking but will not turnover. It started yesterday morning fine, then 5 hours later would not start. Tried this morning, it is a little colder so I tried a jump but it did not work. Maybe no spark, dont know how to chec
by Alex on February 8th, 2009
|
one answer
|
in Ignition control module
92 Buick 3.1 v6 fuel injected, recently, when driving (any speed), the engine will cut out for a half-second or so, then back to normal. Jumper wire gives trouble code 42-Ignition Control Circuit. Any ideas on what to check firs
by neilcc on January 31st, 2009
|
one answer
|
in Ignition control module
Not getting fire from the coil but im getting power to the coil please help
by skeeter1126 on January 31st, 2009
|
3 answers
|
in Ignition control module
My 1988 cavalier loading up with gas in #4 cylinder when I first started working on car I had no spark or fuel. So I replaced ignition module,coil packs and crank sensor. Now I have spark and fuel and #4 cyl is really loading up with gas
by rangerx34 on January 26th, 2009
|
one answer
|
in Ignition control module
CHANGED TIMING CHAIN IN 1997 CHEVY ASTRO VAN AND NOW IT HAS NO IGNETION SPARK AND NO POWER AT THE OBD TERMINAL.
PLEASE HELP
by recovered on January 22nd, 2009
|
one answer
|
in Ignition control module
I have a 2006 chevy coblat it will not go into park so i can't start my car can anyone help
by Anonymous on December 25th, 2008
|
3 answers
|
in Ignition control module
I have a 1985 Lincoln Town Car that will not start. New Battery, Starter Passed AutoZone's test. I replaced the solonoid. It cranked about 5-6 times, will not crank by key. Could something else be shorting the solonoid or could it be
by Craig on December 19th, 2008
|
3 answers
|
in Ignition control module
1989 buick rivera exhust turns cherry red but it does not have a cat.we replaced the computer and checked the crank senor all looks good.any ideas thanks
by ourpaso on December 19th, 2008
|
no answers
|
in Ignition control module
02 taurus V6.72,000 miles At idle it shakes Comp read says #1 cyl missfired & has fuel problem. lite on and it shakes var. speeds. Mechanic changed #1injector,sp plugs still same. He now says brain intermittent prob. new com,used com,reboot .help please
by Anonymous on December 15th, 2008
|
no answers
|
in Ignition control module