by Anonymous on March 28th, 2007

Question

Help answer this question below.

Why wont a standard tranny shift into gear on a 97 gmc 4.3l v6. It starts but just grinds. The clutch pedel has no resistance

Like
Report

Share:: Facebook; Twitter; Other

Answers. Showing one answer.

by littleknown on March 28th, 2007
Check the fluid first, clutch cylinder should be right along side of the master cylinder.
Have you tried starting it in gear? If it bolts forward, then the throw out bearing is history. Throw-out bearing gone, replace the clutch.
Comments
Add a comment...
- Like
- Report
No comments. Post one | Permalink

Did this answer your question? If not, then ask a new question or create a poll.

More Questions. Additional questions in this category.

Does the GM 3.6L engine use a timing chain in the GMC Acadia?
by Answerbag Staff on August 22nd, 2010 | 1 person likes this
Where is the temperature sensor on a 1996 GMC Jimmy located?
by Answerbag Staff on August 16th, 2010 | 1 person likes this
Where is the temperature sensor on a gmc 4.3?
by Answerbag Staff on August 16th, 2010 | 1 person likes this
does my 2004 duramax have a 105 amp alt or a 145 amp alternator?
by chuckman on November 12th, 2011 | 1 person likes this
where is gmc sierra 2003 v8 5.3L crankshaft position sensor located?
by travtrav808 on May 17th, 2011 | 1 person likes this
More GMC trucks See only professionally researched GMC trucks questions

You're reading Why wont a standard tranny shift into gear on a 97 gmc 4.3l v6. It starts but just grinds. The clutch pedel has no resistance

Follow us on Facebook!

Related Ads

Professionally Researched

About Us

About Answerbag

Sitemap

Professionally Researched Questions

Legal

Privacy Policy

Terms of Use

Disclaimer

Ad Choices
Follow Us on Facebook

Answerbag.com
Your favorite Q&A site is on Facebook! Become a fan to connect with the ever-growing community of Answerbaggers, share your thoughts and find out what Answerbag's up to next!
Latest Tweet

What is the very worst thing you can do in an interview? http://t.co/3QoM2mLE

Follow Answerbag on Twitter!

Answerbag

Question

Why wont a standard tranny shift into gear on a 97 gmc 4.3l v6. It starts but just grinds. The clutch pedel has no resistance

Answers. Showing one answer.

Comments

Did this answer your question? If not, then ask a new question or create a poll.

More Questions. Additional questions in this category.

Follow us on Facebook!

Related Ads

Related Questions

I was driving down road felt pop in clutch pedal on a 96 ford contour ls 2.5 v6 mod clutch went to floor would not go into gear turned car off put in gear drove to gas station speed shifting clutch came back up but wont shift is this the clutch or tranny?

I have a 91 GMC Jimmy with a 4.3L I just got running ok. Changed the fuel pump and filter, went to Change the oxygen sensor and now it wont start and has gas dripping out of an exhaust leak near the sensor I replaced. Can any body please help?

I have a 1991 GMC Safari with 4.3L V6 recently its been running a little rougher than normal and the exhaust smells a little like rotten eggs. Could it just be in need of a good tune-up?

97 s10 blazer with 4.3L V6 Vortec, i just changed intake manifold gasket and restabbed the distributor. Everything ran great but the it started surging, almost like it was running out of fuel, I have replaced fuel filter but it still does it?

My tranny wont shift into gear, on my 93 ranger. i tried shifting it on and off, i had no fluid when it went like this, but now i do and it still wont shift, did i burn my clutch or somethin up? what should i do?

Professionally Researched

What is the oil capacity in a chevy 1500 z71 4x4 5.3l?

Where is the crankshaft position sensor on a 93 Camaro V6 3.4 l?

How many quarts of oil does a Toyota 4Runner V6 take?

What kind of transmission fluid is used for a 2008 4.3 V6 truck?

Are V6 engines better on gas than 4-cylinder?

Answerbag.com
Your favorite Q&A site is on Facebook! Become a fan to connect with the ever-growing community of Answerbaggers, share your thoughts and find out what Answerbag's up to next!

Question

Why wont a standard tranny shift into gear on a 97 gmc 4.3l v6. It starts but just grinds. The clutch pedel has no resistance

Answers. Showing one answer.

Comments

Did this answer your question? If not, then ask a new question or create a poll.

More Questions. Additional questions in this category.

Follow us on Facebook!

Related Ads

Related Questions

Professionally Researched

Answerbag.com Your favorite Q&A site is on Facebook! Become a fan to connect with the ever-growing community of Answerbaggers, share your thoughts and find out what Answerbag's up to next!

Answerbag.com
Your favorite Q&A site is on Facebook! Become a fan to connect with the ever-growing community of Answerbaggers, share your thoughts and find out what Answerbag's up to next!