by Anonymous on September 20th, 2006

Question

Help answer this question below.

I own a 1984 chevy S-10, with a 2.8L V-6 carberated. It has a rod knocking. I also have an engine from a 1990 S-10 2.8L V-6, that ahs TBI. what do I have to do to swap them? I want to use the 1990 engine in the 1984, what is invloved in change over?

Like
Report

Share:: Facebook; Twitter; Other

Answers. 2 helpful answers below.

by Darryl61 on September 20th, 2006
If you want to use the fuel inj. you will have to have the complete wiring harness out of the 90 as well. It would be simpler to put the carb and intake manifold from the 84 onto the 90 engine.
Comments
Add a comment...
- Like
- Report
No comments. Post one | Permalink
by terrybrady on September 13th, 2011
You should not have much trouble switching engines but all of the 90 components must be swithed with the engine. I am looking for a 85 carberated engine wiring harness and would buy yours if you switch. Good luck, Terry, terry@homeschoolingusa.com
Comments
Add a comment...
- Like
- Report
No comments. Post one | Permalink

Did this answer your question? If not, then ask a new question or create a poll.

More Questions. Additional questions in this category.

Can you use fiberglass on an intake manifold?
by Answerbag Staff on June 3rd, 2010 | 1 person likes this
What does a turbo timer do?
by Answerbag Staff on May 8th, 2010 | 1 person likes this
Can a sliding window be replaced with a power rear window?
by Answerbag Staff on May 4th, 2010 | 1 person likes this
where is the airbag control module located on my rover 214 si 1996
by matthew.i.greenwood on May 7th, 2012 | 1 person likes this
Have you checked your blinker fluid in your car lately?
by Wiseacre on May 8th, 2012 | 4 people like this
More More Auto and truck parts, maintenance, and tuning See only professionally researched More Auto and truck parts, maintenance, and tuning questions

You're reading I own a 1984 chevy S-10, with a 2.8L V-6 carberated. It has a rod knocking. I also have an engine from a 1990 S-10 2.8L V-6, that ahs TBI. what do I have to do to swap them? I want to use the 1990 engine in the 1984, what is invloved in change over?

Follow us on Facebook!

Related Ads

Professionally Researched

ANSWERBAG BUZZ

1984 s 10 2 3l

1984 chevy s 10 wiring harness

Tbi wrining 2 8v

How to change the water pump in an 2 8l 1984 s10

1990 chevy s10 with 2 8 motor fuel filter

About Us

About Answerbag

Sitemap

Professionally Researched Questions

Legal

Privacy Policy

Terms of Use

Disclaimer

Ad Choices
Follow Us on Facebook

Answerbag.com
Your favorite Q&A site is on Facebook! Become a fan to connect with the ever-growing community of Answerbaggers, share your thoughts and find out what Answerbag's up to next!
Latest Tweet

What is the very worst thing you can do in an interview? http://t.co/3QoM2mLE

Follow Answerbag on Twitter!

Answerbag

Question

I own a 1984 chevy S-10, with a 2.8L V-6 carberated. It has a rod knocking. I also have an engine from a 1990 S-10 2.8L V-6, that ahs TBI. what do I have to do to swap them? I want to use the 1990 engine in the 1984, what is invloved in change over?

Answers. 2 helpful answers below.

Comments

Comments

Did this answer your question? If not, then ask a new question or create a poll.

More Questions. Additional questions in this category.

Follow us on Facebook!

Related Ads

Related Questions

Where is the fuel filter on 1987 chevy s10 tahoe 2.8l engine

I have a 1984 chevy s10 2.8L stick shift transmission is bad. i also have a 1986 s10 2.5L automatic the motor is locked up. I am putting the tranny out of the 86 in the 84 because it will bolt up. what all do i need to convert the 84 to an automatic.

While driving at 20MPH loud grind noise was heard, engine stopped. Engine will not start, starter turns over engine very slowly. Starter, battery o.k. Chev S10 2.8 v6 100,000 miles.

I have a 1986 chevy s10 with a 2.5L transmission the motor is locked up. Will a 1984 chevy s10 2.8L motor bolt up to the tranmission. what is needed. the transmission in the 84 is a stick shift. but i am converting it to automatic. plz let me know.

My '85 S10 2.8L V6 has a strange substance in it, when cold oil is thick with a "glitter" and when started I see nothing but a glaze on dipstick. Also it's eating the oil cap but idles fine. How do I troubleshoot?

Professionally Researched

How many miles per gallon does a 93 Chevy S-10 V-6 get?

Where is the fuel pump relay circuit on a 1997 Chevy S-10 2.2l engine?

Does the Dodge Caravan have a 3.8l engine?

How many cylinders does the V-6 engine have?

How many quarts go into a 3.5l v6 lincoln mkz car engine?

ANSWERBAG BUZZ

Answerbag.com
Your favorite Q&A site is on Facebook! Become a fan to connect with the ever-growing community of Answerbaggers, share your thoughts and find out what Answerbag's up to next!

Question

I own a 1984 chevy S-10, with a 2.8L V-6 carberated. It has a rod knocking. I also have an engine from a 1990 S-10 2.8L V-6, that ahs TBI. what do I have to do to swap them? I want to use the 1990 engine in the 1984, what is invloved in change over?

Answers. 2 helpful answers below.

Comments

Comments

Did this answer your question? If not, then ask a new question or create a poll.

More Questions. Additional questions in this category.

Follow us on Facebook!

Related Ads

Related Questions

Professionally Researched

ANSWERBAG BUZZ

Answerbag.com Your favorite Q&A site is on Facebook! Become a fan to connect with the ever-growing community of Answerbaggers, share your thoughts and find out what Answerbag's up to next!

Answerbag.com
Your favorite Q&A site is on Facebook! Become a fan to connect with the ever-growing community of Answerbaggers, share your thoughts and find out what Answerbag's up to next!