by anthony on August 24th, 2007

Question

Help answer this question below.

I have a 1988 ford E-250 van. It has a fuel injected 4.9L 300c.i. 6 cyl. I replaced the ecu, ignition module, checked the fuel rail-all fine and the rail has good pressure. But it just wont start even though i drove it there last year. What's wrong?

Like
Report

Share:: Facebook; Twitter; Other

Answers. 2 helpful answers below.

by n73603 on April 30th, 2009
check the ECM Relay, I beleave that yoar still has one, it will usually be on the drivers side inner finder well area remember it is the RELAY your looking for, also check EcM Fuse and Ing. Fuse as well. also look for bad connection at the Relay as well
Comments
Add a comment...
- Like
- Report
No comments. Post one | Permalink
by specialk on January 6th, 2008
check the plugs make sure they arent fouled out. also check the cap and rotor.
Comments
Add a comment...
- Like
- Report
No comments. Post one | Permalink

Did this answer your question? If not, then ask a new question or create a poll.

More Questions. Additional questions in this category.

Where Is the ECU Located in a Ford Flex?
by Answerbag Staff on August 17th, 2010 | 1 person likes this
Where is the EGR valve located on a 1989 Ford 2.9?
by Answerbag Staff on August 15th, 2010 | 1 person likes this
I have a ford fiesta encore 1.3 - the air blower has stuck on cold - it will not dispense hot air .. Can anyone tell me how to fix this?
by sussexsi on March 1st, 2011 | 1 person likes this
What does the 1965 Ford Falcon identification tag mean?
by Answerbag Staff on August 11th, 2010 | 1 person likes this
Will a radiator from a 1996 ford explorer fit in a 1996 ford 150?
by prttyone8 on March 11th, 2011 | 1 person likes this
More Ford models See only professionally researched Ford models questions

You're reading I have a 1988 ford E-250 van. It has a fuel injected 4.9L 300c.i. 6 cyl. I replaced the ecu, ignition module, checked the fuel rail-all fine and the rail has good pressure. But it just wont start even though i drove it there last year. What's wrong?

Follow us on Facebook!

Related Ads

Professionally Researched

ANSWERBAG BUZZ

1988 ford van 300c i no spark

1988 ford f150 4 9l fuel pump fuse

1989 f150 efi 300 turns over but wont start

1988 ford van fuel filter 4 9

1988 ford van fuel system

About Us

About Answerbag

Sitemap

Professionally Researched Questions

Legal

Privacy Policy

Terms of Use

Disclaimer

Ad Choices
Follow Us on Facebook

Answerbag.com
Your favorite Q&A site is on Facebook! Become a fan to connect with the ever-growing community of Answerbaggers, share your thoughts and find out what Answerbag's up to next!
Latest Tweet

What is a movie that was ignored you thought great? http://t.co/FsBFmVd7

Follow Answerbag on Twitter!

Answerbag

Question

I have a 1988 ford E-250 van. It has a fuel injected 4.9L 300c.i. 6 cyl. I replaced the ecu, ignition module, checked the fuel rail-all fine and the rail has good pressure. But it just wont start even though i drove it there last year. What's wrong?

Answers. 2 helpful answers below.

Comments

Comments

Did this answer your question? If not, then ask a new question or create a poll.

More Questions. Additional questions in this category.

Follow us on Facebook!

Related Ads

Related Questions

I have a 1989 Ford F150 4.9L EFI that turns over but won't start. So far I've replaced the TPS, plugs, cap and rotor, ign. module, fuel filter. Has spark and plugs are wet with fuel. No water present in fuel. Verified ign. timing. What could be wrong?

I have an 1988 Ford Ranger with 2.9L. The truck will start fine and run forever until you kill it. The fuel pump comes on and pressures up the fuel rail but it does not get any fire. I can let it sit for about 10 minutes and it will start up fine.

I have a 1988 ford ranger 2.9L fuel injected, It starts up and runs fine but the longer it runs the worse it gets, doesn't want to start, fuel likes to give out ect.?

I have a 1998 ford explorer that has spark and fuel but won't start and i have replaced the ignition module with the coil pack,the crank sensor,and have checked the fuel pressure 40lbs. What else should I check?

What is wrong with a 94 ford explorer 4x4 v6 that cranks and wont start. ICM is good, no oil on plugs,(brand new) ig coils test fine, has compression, fuel pump works, brand new starter.

Professionally Researched

What is the fuel pressure specification for a 1996 dodge 3.9l?

What is the fuel pressure needed for a fuel injected motor?

Where is the fuel filter on a fuel injected 1997 Ford Escort LX?

Is a 1988 Honda Accord fuel injected?

Is the 1995 Ford Explorer fuel injected?

ANSWERBAG BUZZ

Answerbag.com
Your favorite Q&A site is on Facebook! Become a fan to connect with the ever-growing community of Answerbaggers, share your thoughts and find out what Answerbag's up to next!

Question

I have a 1988 ford E-250 van. It has a fuel injected 4.9L 300c.i. 6 cyl. I replaced the ecu, ignition module, checked the fuel rail-all fine and the rail has good pressure. But it just wont start even though i drove it there last year. What's wrong?

Answers. 2 helpful answers below.

Comments

Comments

Did this answer your question? If not, then ask a new question or create a poll.

More Questions. Additional questions in this category.

Follow us on Facebook!

Related Ads

Related Questions

Professionally Researched

ANSWERBAG BUZZ

Answerbag.com Your favorite Q&A site is on Facebook! Become a fan to connect with the ever-growing community of Answerbaggers, share your thoughts and find out what Answerbag's up to next!

Answerbag.com
Your favorite Q&A site is on Facebook! Become a fan to connect with the ever-growing community of Answerbaggers, share your thoughts and find out what Answerbag's up to next!