Wood carving.

How much wood COULD a wood chopper chop?
by Reecebullet on November 5th, 2011 | 1 person likes this | 5 answers | in Wood carving

by Anonymous on December 31st, 1969 | no answers | in

What are you hiding in the basement or closet?
by HoboJoe on October 25th, 2011 | 4 people like this | 9 answers | in Wood carving

How can I rehydrate a cracked, checkered and desiccated wood log?
by morningbear on June 28th, 2010 | one answer | in Wood carving

DIFFERENCE BETWEEN PNEUMATIC NAILS WILL ANY NAIL WORK
by POWERMAN1 on January 17th, 2010 | one answer | in Wood carving

I was thinking of starting wood carving what would i need to start
by hong kong phooey on November 29th, 2009 | 4 answers | in Wood carving

Hi there folks, Just wanted to know what kind of Teak you could suggest that I use for my decking. Does country of origin and quality of wood matter? Any suggestions much appreciated
by WoodyWoodPecker on November 18th, 2009 | one answer | in Wood carving

If i want to carve a morning dove out of wood ,,, should i use morning wood ? ;-)
by The Anonymous Witch on October 19th, 2009 | 11 answers | in Wood carving

What is the best wood to use to make a storage device. 4mm MDF wood or 6mm MDF wood?
by darkness on September 8th, 2009 | one answer | in Wood carving

Tung Oil as a wood sealer/finish, I'm making my own chopsticks and am looking for an alternative to enamels and other synthetic finishes. I'm thinking of using Shellac over Tung Oil, will this combo be alright? Do I even need both, will one do fine?
by TheGoldenPoo on August 24th, 2009 | 2 answers | in Wood carving

Id like to put a radius on a board thats 7 ft long,how do i make the radius
by moodyblue on August 22nd, 2009 | one answer | in Wood carving

I have a set of verry old glass cabinet knobs that attach to drawers by tapping the door and threading the knob into them as opposed to using a screw from the back. The knob has a very course thread about 11.5 pitch and is about half an inch in dia.. Is a
by Danaman on July 12th, 2009 | no answers | in Wood carving

If you were going to make something, woodwork, to sell at a small town craft fair, what would you make? Looking for ideas that will be a big hit. Something modern, HGTV style.
by Anonymous on May 4th, 2009 | 2 answers | in Wood carving

Have you ever seen the carving of a Totem pole?
by Colt COAT of Justice on March 31st, 2009 | 2 answers | in Wood carving

Do you know how to wood carve?
by Michael wears a COAT of loyalty on February 12th, 2009 | 6 answers | in Wood carving

Do you ever whittle with a pocket knife to pass the time?
by Colt COAT of Justice on February 12th, 2009 | 2 answers | in Wood carving

Describe the 2 common methods of dimensinoning for darwing that must read in mtric or costumary measurrements.
by Rigi on December 18th, 2008 | one answer | in Wood carving

What are 2 types of drawing most commonly used in woodworking?
by Rigi on December 18th, 2008 | 3 answers | in Wood carving

Assuming you had the skill:If you had to carve something out of a piece of wood what would it be?
by ENigma on December 12th, 2008 | 10 answers | in Wood carving

Apart from basswood, is there another wood suitable for carving for someone just learning the craft?
by sloroller on December 3rd, 2008 | one answer | in Wood carving

How do I carve out the bowl of a wooden spoon? I want to do it quickly and don't want to do it by hand, and we don't have a router either.
by SundaeSarah on October 6th, 2008 | 2 answers | in Wood carving

Has anyone ever built there own kayak? if so how do you go about doing so.
by iolar1013 on July 6th, 2008 | one answer | in Wood carving

How do you sharpen HSS saw blades?
by grizzz on May 13th, 2008 | one answer | in Wood carving

Ware can i find building plains for footboard and ONLY for a footboard NOT a headboard?
by pooke11 on April 30th, 2008 | one answer | in Wood carving